HACCER has devoted to the development of barn door hardware over 10 years, improve and upgrade products to give each family the most appropriate choice. HACCER 5ft sliding barn door hardware kit use for single door (doors not include). Q: How to choose barn door track size? A: Barn door track length should be at least twice of total door width.
For example, if you barn door is 30'' wide, you will need 230'' = 60'' 5FT long track, your opening will show fully, you can use the track which is a little bit longer and please let your door a little bigger than the opening. Q: How much ceiling space requirement of the single door hardware system. A: At least 6 from top of door to ceiling to install.
Q: How much gap of the barn door hardware system? A: The gap between inner door&wall is about 5/8'' based on door thickness 1-9/16'. The barn door hanger roller with Professional bearings, make your bypass barn door hardware service life last longer.Material quality is high purity bearing steel Gcr15, professional bearing materials, ring fixed structure bearing, wraps around the steel ball and prevent steel ball from leaving the locus, make sliding more stable. There is a dust cover the bearing to prevent dust from entering and lubricating oil leakage, let the roller can slide smoothly and more durable. 1 hanger with 2 life time lubricated bearing, ensure sliding balance and stability, test beyond 160,000, you can use it for a long time. The roller surface is covered with nylon, wear-resisting and slide very quietly.
We design the Dowel pin Front part slightly larger, keep the dowel stuck in hole not fall off. All of prat is make by Q235 carbon steel, thick is 1/4'' (6.3mm). 8.8 grade roller bolt can hold the doors comfortably. About all 5 FT Single barn door hardware. On track, make by solid 1/4 thick steel, with 8.8 grade high strengh bearing capacity lag blots, fit for concrete wall and wooden wall.
Provide 1-3/8'' length spacer, fit for door. If your door thickness is greater than. We also more longer spacer. For you to choose from, or you can add a headboard on wall, then install the track.
Prevent the door falling off from the track, one door have 2 stoppers, ensure the stability and safety, with the rubber plug, good damping effect and reduce the noise, have 2 screws to fasten stopper on track, you can put stopper on track where you want to stop your door, easy to remove if you want adjust. Can prevent the door swinging back and forth or against the baseboard, let your door slide on same locus, fit for all thickness with grooved or ungrooved doors. Can prevent door to be lifted off rail when the barn door slide, ensure the stability and safety. Single barn door hardware instructions step by step with fractional measurements in inch, have detailed word instructions with pictures. Q: Can i cut the track?A: Yes, you can cut it into any length of you want. Q: Can i use it for out door? A: We suggest if use for outdoors, you can make some cover above the track, and you need paint and add oil regularly to extended service life. Q: What circumstances do I need to add a headboard? If you have a doorway trim on wall.
If your door thickness is greater than 1-3/4. If the studs don't line up with the pre-drilled holes in the rail. Q: How thick door use for it? What is the weight capacity? A: We suggest 1-3/8" 1-3/4" thick door, if you use for other thick door, please tell us, we will provide some accessories to you.Q: What is the weight capacity? Single barn door hardware kit package include.
2 x Steel Hanger with bolt. 4 x Door Stopper with Hex Wrench. 4 x 1-3/8'' Spacer with lag bolt. 1 x Floor Guide with screw. 2 x Anti-Jumper with screw.1 x Barn Door Hardware Installation Manual. Why choice single barn door hardware system? Single barn door hardware system slides horizontally, it can save space compared with ordinary push door. Decorate your locker room, closet, kitchen, wardrobe, bathroom, bedroom, storeroom, change your home dull image. We have large processing factory and advanced equipment, accept mass customization.
The track drilling hole on wall is = your door height + 1-11/16'. The hanger first hole install on door is 1-9/16 from top of door, second hole is 3-9/16 from first hole.Please reserve 6 space above door to ceiling to install hardware. When door thickness is 1-9/16'', gap between door to walls is 5/8'. The item "5 FT Door Sliding Barn Hardware Kit Hanger Track System Carbon Steel Roller Rail" is in sale since Tuesday, August 31, 2021. This item is in the category "Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware". The seller is "huankun888" and is located in Shenyang.
This item can be shipped worldwide.